The best method would be to pull up the carpet in the rear of the vehicle, looking for an existing hole or knockout. If there is a knockout, remove the center piece and run the wire through. If you cannot find an existing hole, you will have to drill one. Any time you run electrical wiring through the car body, you will want to use a grommet to prevent the wire from rubbing against the opening and eventually shorting out. You will also want to use silicone sealant to seal up the hole around... view full answer...
In order to maintain the battery on your trailer battery I would add the wiring harness to your 2006 Subaru B9 Tribeca. To be clear, the power from your vehicle will not be able to charge the battery, only maintain it. If you need to charge your battery you will need a charger like the # CTEK56353.
You will have to start by adding a 4-way. I recommend the T-One Vehicle Wiring Harness # 118461. This will plug into the connection point in your rear cargo area. I would also choose the Tekonsha... view full answer...
Yes, Thule does list the Passage 2, # TH910XT, as a fit for your 2006 Subaru Tribeca. I have included links to the installation instructions and a video for you to view.
If you will be carrying womens, childrens, or alternative frame bikes, I recommend using the Burke adapter bar, # TH982XT, for greater ground clearance and to carry the bikes more level. I have included a link to a video that shows how the adapter works. view full answer...
To install Curt trailer hitch # C13046 on your 2007 Subaru Tribeca you will only need to temporarily remove the spare tire from under the vehicle. After the hitch is installed, you will put the spare tire back where it was.
There is no mention of having to trim anything on the vehicle to install the hitch. I have linked the instructions for you so you can see what all is involved in the installation. The receiver will be the only part visible once install and will be directly below the... view full answer...
For your 2007 Subaru B9 Tribeca, there is not a confirmed fit for the 1-1/4 inch hitch. Curt does have a 2" fit like you mentioned. The Curt # C13046 is the only hitch available that is confirmed to fit your Tribeca.
Because you do not wish to use a reducer like # HT02 and a hitch lock anti-rattle like # 63232 with your current Kuat NV bike rack with 1-1/4 inch stinger, I recommend you use the Kuat Bike Rack Shank Adapter - 1-1/4" to 2" # D101 which is a fit for your NV with it's integrated... view full answer...
To install the Curt Hitch part # C13046 on your 2007 Subaru B9 Tribeca you will need to temporarily remove your spare tire. You will be able to reinstall it once the hitch is installed.
For trailer wiring I would recommend the Curt Harness part # C59496.
For ball mounts I recommend the etrailer Ball Mount Kit # 989900. It comes with 2 ball mounts, 2 balls, a hitch pin with clip, and a carrying bag. view full answer...
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector Item # C55370 is indeed a confirmed fit for the 2006 Subaru Tribeca. This harness fits a few different Subaru vehicles but we haven't had a Tribeca in to make an installation video. But the manufacturer has tested it on a Tribeca. The video I have linked can be used as a guide since it is a different model and installation will be a bit different. I have also linked the instructions for you. view full answer...
You will first want to measure your vent, not the actual cover on your trailer. The vents are 14-1/2 by 14-1/2 inches, 14 by 14 inches, or 13 by 14 inches, in size.
Then you will want to make sure the correct size cover uses the same type of hinge as shown on the product page. Usually it will be a rolled metal edge, and you will be able to use the picture on our site to compare to your cover..
The item you selected, Ventline Smoke Dome, part # BV0554-03, is a replacement cover for a 14-1/4... view full answer...
The Brophy Scissors Steps, part # SS04 can be mounted to a camper without holding tanks. These steps are only to be used while vehicle is stationary. They are not made to be permanently mounted to the camper. It needs to be installed using the mounting bracket that attaches to the camper. With the mounting bracket installed on the camper the steps are easily removed prior to vehicle travel. view full answer...
Go To Results